DIN EN 300019-2-4-2004 设备工程(EE).电信设备的环境条件和环境试验.第2-4部分:环境试验规范.非抗大气影响场所用固定设备
作者:标准资料网 时间:2024-05-16 22:35:24 浏览:8921
来源:标准资料网
【英文标准名称】:EquipmentEngineering(EE)-Evironmentalconditionsandenvironmentaltestsfortelecommunicationsequipment-Part2-4:Specificationofenvironmentaltests;Stationaryuseatnon-weatherprotectedlocations(EndorsementoftheEnglishversionEN300019-
【原文标准名称】:设备工程(EE).电信设备的环境条件和环境试验.第2-4部分:环境试验规范.非抗大气影响场所用固定设备
【标准号】:DINEN300019-2-4-2004
【标准状态】:现行
【国别】:德国
【发布日期】:2004-03
【实施或试行日期】:
【发布单位】:德国标准化学会(DIN)
【起草单位】:
【标准类型】:()
【标准水平】:()
【中文主题词】:远程通信;电信;耐力;极限(数学);定义;气候试验;固定的;通信设备;环境;仪器;装置配置;仪器工艺;应用;环境条件;试验;电气工程;环境试验;分类;环境影响;气候条件
【英文主题词】:
【摘要】:ThisEuropeanstandardspecifiesrequirementsinthetelecommunicationssector.
【中国标准分类号】:M04
【国际标准分类号】:33_050_01
【页数】:2P;A4
【正文语种】:德语
【英文标准名称】:TestMethodforEvaluatingThinFilmFluidLubricantsinaDrainandDryModeUsingaPinandV-BlockTestMachine(05.03)
【原文标准名称】:在排水和干燥模式下利用针式和V-块式试验机评价薄膜流动性润滑剂性能的测试方法(05.03)
【标准号】:ANSI/ASTMD5620-1999
【标准状态】:作废
【国别】:美国
【发布日期】:1999
【实施或试行日期】:
【发布单位】:美国国家标准学会(US-ANSI)
【起草单位】:ANSI
【标准类型】:()
【标准水平】:()
【中文主题词】:校正;排水管;润滑剂;材料试验机;牛顿流体;石油产品;水
【英文主题词】:Calibration;Drains;Lubricants;Materialtestingmachines;Newtonianfluids;Petroleumproducts;Water
【摘要】:Thistestmethodcoversthedeterminationoftheendurance(wear)lifeandloadcarryingcapacityofthinfilmfluidlubricantsthatareintendedtooperateafterasingleapplicationandafterexcessmaterialhasdrainedfromthecontactareaofslidingmetaltometalsurfaces,andwhichoperatesinwhatfunctionallyisadrainanddrymodewithnoadditionallubricantbeingapplied.ThevaluesstatedinSIunitsaretoberegardedasthestandardexceptwhereequipmentissuppliedusinginch-poundunitswhichwouldthenberegardedasthestandard.Thevaluesgiveninparenthesesareforinformationonly.Thisstandarddoesnotpurporttoaddressallofthesafetyconcerns,ifany,associatedwithitsuse.Itistheresponsibilityoftheuserofthisstandardtoestablishappropriatesafetyandhealthpracticesanddeterminetheapplicabilityofregulatorylimitationspriortouse.
【中国标准分类号】:E34
【国际标准分类号】:75_100
【页数】:
【正文语种】:英语
Product Code:SAE J200
Title:Classification System for Rubber Materials
Issuing Committee:Committee On Automotive Rubber Specs
Scope:This classification system tabulates the properties of vulcanized rubber materials (natural rubber, reclaimed rubber, synthetic rubbers, alone or in combination) that are intended for, but not limited to, use in rubber products for automotive applications.The SAE Committe on Automotive Rubber Specifications (CARS) has the sole responsibility for SAE J200. CARS Works closely with and receives input from ASTM Subcommittee D11.30 on Classification of Rubber Compounds with the goal to keep SAE J200 and ASTM D 2000 technically equivalent. Candidate materials presented for development of new tables or for inclusion in Tables A1 or A2 of SAE J200 or Table X1.1 of ASTM D 2000 shall be initiated with the SAE CARS Committee. The procedure to be followed is detailed in Appendix C of SAE J200.This document may serve many of the needs of other industries in much the same manner as SAE numbered steels. It must be remembered, however, that this system is subject to revision when required by automotive needs. It is recommended that the latest revision always be used. This document is based on the premise that all rubber materials intended for use in rubber products can be arranged into characteristic designations. These designations are determined by types, based on resistance to heat aging, and classes, based on resistance to swelling by oil. Basic levels are thus established which, together with values describing additional requirements, permit complete description of the quality of all rubber materials. In all cases where provisions of this document would conflict with those of the detailed specifications for a particular product, the latter shall take precedence.When the rubber product is to be used for purposes where the requirements are too specific to be completely prescribed by this classification system, it is necessary for the purchaser to consult the supplier in advance to establish the appropriate properties, test methods, and specification test limits.
